A battery strapping tool tensions, friction-welds and cuts PET or PP band in one cordless cycle. AECSORIX tools cover 13–19 mm band with 600–3500 N adjustable tension, an LCD setting and two 4.0 Ah batteries — one portable tool for cartons, timber, steel coils and stone. This guide covers the specifications that matter, how to match band and tension to a load, and what to check when a joint fails.
What a battery strapping tool does
A cordless strapping tool does three jobs in sequence: it pulls the band tight around the load to a set tension, joins the overlap with a friction weld (a fast spinning friction wheel melts the thermoplastic band), and cuts off the tail. Because it runs on batteries, the operator can strap a load anywhere — on a pallet, in a truck, or in a yard — with no air hose or compressor. AE01 and AE02 use the same 3500 N platform and accept 13–19 mm PET and PP band.
Specifications that actually matter
| Specification | AECSORIX AE01 / AE02 | Why it matters |
|---|---|---|
| Band width | 13–19 mm | Covers light cartons through heavy steel coils with one tool |
| Tension range | 600–3500 N, LCD set | Repeatable setting so every operator applies the same force |
| Joint strength | around 75% of band strength | With correct band and tension; the weld is not the weak point |
| Band material | PET and PP | One tool for both materials, only the tension changes |
| Batteries | 2 × 4.0 Ah (18V / 21V) | One charges while the other works |
| Charge time | 90–120 minutes | Charger accepts 100–245 VAC; correct plug supplied per country |
PET vs PP: which band should you use
Use PET for heavy, rigid loads that need high retained tension; use PP for lighter, compressible loads where cost matters most. Both work with the same tool.
| Property | PET | PP |
|---|---|---|
| Tensile strength | Higher | Lower |
| Tension retention | Excellent | Moderate |
| Typical loads | Steel, timber, brick, stone | Cartons, light bundles |
| Cost | Higher | Lower |
For the reasoning behind this choice, see PET vs PP strapping: how to choose the right band.
Choosing band width by load
| Load | Band | Width | Starting tension |
|---|---|---|---|
| Cartons, light bundles | PP | 13 mm | 600–1200 N |
| Timber, wooden crates | PET | 13–16 mm | 1500–2500 N |
| Steel coils, brick, stone | PET | 16–19 mm | 2500–3500 N |
| Plastic pipe bundles | PET or PP | 13–16 mm | Depends on diameter |
These are starting points, not fixed rules — confirm with a test joint on your own load. The full reasoning is in 13mm or 19mm strapping? A buyer’s guide to band width and how to choose a tool by load type.
AE01 vs AE02
AE01 and AE02 share the same core platform: 3500 N tension, 13–19 mm band range, LCD control and two 4.0 Ah batteries. They differ in exterior appearance and colour, not in pulling power or capacity. If you are comparing the two, read AE01 vs AE02: what actually differs. For the product specifications themselves, see AE01 and AE02.
Kit contents and spare parts
One kit contains the tool, two 4.0 Ah batteries, a charger (100–245 VAC), toolkit, carrying bag and a carton with foam insert. Wear parts are stocked separately: BB4003, BB2006, BB6004, BB6003 and OUT405. Replace the cutter and friction wheel on schedule — worn parts are the main cause of weak welds, as explained in battery strapping tool troubleshooting.
From battery to pneumatic, and tension control
If you are deciding whether to move away from air-powered tools, battery vs pneumatic strapping tools compares mobility, power consistency and running cost. Once you have the right band, set tension correctly using how to adjust strapping tension (600–3500 N). For heavy coils specifically, follow how to strap steel coils safely.
Frequently asked questions
Need a recommendation or a quote? Send your strap width, load and quantity to AECSORIX, or WhatsApp +86 13606818153. We reply within 12 working hours.
